[ROM][JB.16][CDMA] BloodRage v1.3 *Update* 9/9

First time I went into no frills it read 300-1.2, I chose 1.2 and rebooted. It then read 300-1.325, I chose 1.325 and rebooted. Max reads 1.2

OK so I understand here you rebooted after selecting the max frequency each time? All you should have to do is uncomment the scripts and reboot once.

OK...and the max freq should read 1.325?

It should lol! Just make sure after you uncomment the scripts and reboot you do the refresh frequencies option in no frills.

OK...it still reads current as 1.2 and requested 1.325 and the refresh is checked...maybe I am not doing it in the right order...I'm gonna dirty flash again and run through the steps and see if it works...lol

OK bud if you don't get it sit tight I'm working on something on my end. But I get up at 230a for work so I gotta crash. Keep me posted.

OK no problem... I dirty flashed...uncommented scripts and rebooted
once...it shows current 1.2 requested 1.325. I didn't choose or apply anything

OK, like Nosnhoj, i have installed SetCPU and it says 1050 MHz as current and right below that "1200 max 300 min".
The adjustable slider bars on lower half of screen show 1320 MHz Max, and 300 MHz Min. Set on Boot is unchecked. "Performance" and "Deadline" are currently selected on very bottom options.

I went ahead and adjusted the Max slider bar down a couple notches and then back up to the max of 1320. when i did this the Current reading changed down then all the way back up to 1325, and the grayed out text of min/max directly below that finally changed up to the 1320 reading.
when i Linpack test at the 1320 (when comming from SetCPU) i get the MOST consistent results..48.2-48.8. at the lower 1050 current with 1200 max showing it get 37-39 results...
Here is the odd part. While typing this i let the phone's screen turn off, when i turn it back on the "Current" cpu drops down to 1050, and the Gray #'s directly below that go back down to "1200 max 300 min"... and again when i adjust the slider option just enough to get it off 1320 and then right back to it, the current and grayed #'s bounce back up to 1320

the profile is set to exclusive with a priority of 100.

side note, when i check out the Governor tab, it says "The curret governor, performance, does not support this menu..."

any ideas?

Try this... put the comment (#) back in front of the echo 0 command line. Then save changes select brick exit the app and reboot. Let me know if that changes things.

echo 1 575 1200 > /proc/cpu_control/tweak_cpu
echo 2 800 1325 > /proc/cpu_control/tweak_cpu
echo 3 1050 1388 > /proc/cpu_control/tweak_cpu
echo 4 1325 1398 > /proc/cpu_control/tweak_cpu

Try deleting the entire echo 0 line. John did this and it worked for him.

Commenting out did not fix it. Just want to make sure that all of the "insmod" lines are "uncommented". And I have selected "SU" and "boot" on the 90modules options.

I'll try deleting it. Be right back.

Can you copy/ paste the entire script in a post for me?

It's still doing it. And the 300mHz option is still their in setCPU even after I removed the line from 90 modules.

#!/system/bin/sh
#
#--------------------------------------------------------------------

# Load Modules

insmod /system/lib/modules/symsearch.ko
insmod /system/lib/modules/cpufreq_interactiveX.ko
insmod /system/lib/modules/cpufreq_hotplugX.ko
insmod /system/lib/modules/cpufreq_smartass2.ko
insmod /system/lib/modules/cpufreq_pegasusq.ko
insmod /system/lib/modules/cpufreq_boostedASS2.ko
insmod /system/lib/modules/cpu_control.ko
insmod /system/lib/modules/sio-iosched.ko


echo 1 575 1200 > /proc/cpu_control/tweak_cpu
echo 2 800 1325 > /proc/cpu_control/tweak_cpu
echo 3 1050 1388 > /proc/cpu_control/tweak_cpu
echo 4 1320 1398 > /proc/cpu_control/tweak_cpu

Is it something stupid, like having to remove all of the "#" gettin the script? That would be my luck.

It is OK that 300 is still min. Don't worry about the benchmarks in your profile for screen on did you readjust the frequencies to 1325 max? Make sure you did after reading your post again it seems like your profile isn't sticking. Everything else makes sense. The frequencies don't automatically change in setcpu you have to toggle the slider. But they should stick if profile is properly set. Also make sure you enabled profiles. Lol!

"Enable Profiles" is selected.
I do not have it set to 1325. It's set to 1320, that's what my copy+ paste of the file shows. The slider bars should fallow what ever I set the 90modules tip right? Our are you saying that I need to put 90... at 1325 and not mess with it?

No 1320 is fine. So I understand when you slide max freq to 1320 the current freq is shown at 1050? Or its just changing back after screen off? Sorry but sometimes its hard to gather info. Your scripts look fine. I'm just trying to understand why this is such a pain in the ass. Lol!

echo 0 300 1025 > /proc/cpu_control/tweak_cpu
echo 1 575 1200 > /proc/cpu_control/tweak_cpu
echo 2 800 1325 > /proc/cpu_control/tweak_cpu
echo 3 1050 1388 > /proc/cpu_control/tweak_cpu
echo 4 1325 1398 > /proc/cpu_control/tweak_cpu

This is a copy of my table and it is working fine. I tested this on 3 separate test versions without fail and I'm stumped why it isn't working for everyone. Sorry man. I may just have to make this a flash able mod like on rage. But with only one flash.

Where is enabled profiles located?

At the bottom of the profiles menu in setcpu.

OK I don't know wtf just happened or why but now no frills is showing max freq and current is 1.325

And where is setcpu?

Nosnhoj wrote:OK I don't know wtf just happened or why but now no frills is showing max freq and current is 1.325

Well good!!! Setcpu is a different app. Lol. In no frills just make sure you enter settings and select refresh frequencies.

Oh and in this forum you can feel free to say what the fuck. Lol!